ATV12H018M2 variable speed drive ATV12 – 0.18kW – 0.25hp – 200..240V – 1ph
Original price was: ₹18468.₹7387Current price is: ₹7387.
HSN CODE: 85044090
- Description
- Reviews (0)
Description
product destination | Asynchronous motors |
---|---|
component name | ATV12 |
built-in fan | Without |
network number of phases | 1 phase |
motor power kW | 0.18 kW |
motor power hp | 0.25 hp |
line current | 3.4 A at 200 V 2.8 A at 240 V |
speed range | 1…20 |
IP degree of protection | IP20 without blanking plate on upper part |
range of product | Altivar 12 |
product or component type | Variable speed drive |
product specific application | Simple machine |
communication port protocol | Modbus |
[Us] rated supply voltage | 200…240 V – 15…10 % |
EMC filter | Integrated |
supply frequency | 50/60 Hz +/- 5 % |
---|---|
connector type | 1 RJ45 (on front face) for Modbus |
physical interface | 2-wire RS 485 for Modbus |
transmission frame | RTU for Modbus |
transmission rate | 4800 bit/s 9600 bit/s 19200 bit/s 38400 bit/s |
number of addresses | 1…247 for Modbus |
communication service | Read holding registers (03) 29 words Write single register (06) 29 words Write multiple registers (16) 27 words Read/write multiple registers (23) 4/4 words Read device identification (43) |
continuous output current | 1.4 A at 4 kHz |
maximum transient current | 2.1 A for 60 s |
speed drive output frequency | 0.5…400 Hz |
braking torque | Up to 70 % of nominal motor torque without braking resistor |
output voltage | 200…240 V 3 phases |
electrical connection | Terminal, clamping capacity: 3.5 mm², AWG 12 (L1, L2, L3, U, V, W, PA, PC) |
tightening torque | 0.8 N.m |
insulation | Electrical between power and control |
supply | Internal supply for reference potentiometer: 5 V DC (4.75…5.25 V), <10 mA, protection type: overload and short-circuit protection Internal supply for logic inputs: 24 V DC (20.4…28.8 V), <100 mA, protection type: overload and short-circuit protection |
analogue input type | Configurable current AI1 0…20 mA 250 Ohm Configurable voltage AI1 0…10 V 30 kOhm Configurable voltage AI1 0…5 V 30 kOhm |
discrete input type | Programmable LI1…LI4 24 V 18…30 V |
discrete input logic | Negative logic (sink), > 16 V (state 0), < 10 V (state 1), input impedance 3.5 kOhm Positive logic (source), 0…< 5 V (state 0), > 11 V (state 1) |
sampling duration | 20 ms, tolerance +/- 1 ms for logic input 10 ms for analogue input |
linearity error | +/- 0.3 % of maximum value for analogue input |
analogue output type | AO1 software-configurable voltage: 0…10 V, impedance: 470 Ohm, resolution 8 bits AO1 software-configurable current: 0…20 mA, impedance: 800 Ohm, resolution 8 bits |
discrete output type | Logic output LO+, LO- Protected relay output R1A, R1B, R1C 1 C/O |
minimum switching current | 5 mA at 24 V DC for logic relay |
maximum switching current | 2 A 250 V AC inductive cos phi = 0.4 L/R = 7 ms logic relay 2 A 30 V DC inductive cos phi = 0.4 L/R = 7 ms logic relay 3 A 250 V AC resistive cos phi = 1 L/R = 0 ms logic relay 4 A 30 V DC resistive cos phi = 1 L/R = 0 ms logic relay |
braking to standstill | By DC injection, <30 s |
frequency resolution | Analog input: converter A/D, 10 bits Display unit: 0.1 Hz |
time constant | 20 ms +/- 1 ms for reference change |
functionality | Basic |
specific application | Commercial equipment |
Variable speed drive application selection | Mixer Commercial equipment Other application Commercial equipment Ironing Textile |
motor starter type | Variable speed drive |
discrete input number | 4 |
discrete output number | 2 |
analogue input number | 1 |
analogue output number | 1 |
asynchronous motor control profile | Voltage/frequency ratio (V/f) Sensorless flux vector control Quadratic voltage/frequency ratio |
transient overtorque | 150…170 % of nominal motor torque depending on drive rating and type of motor |
acceleration and deceleration ramps | U Linear from 0 to 999.9 s S |
motor slip compensation | Preset in factory Adjustable |
switching frequency | 2…16 kHz adjustable 4…16 kHz with derating factor |
nominal switching frequency | 4 kHz |
prospective line Isc | 1 kA |
protection type | Line supply overvoltage Line supply undervoltage Overcurrent between output phases and earth Overheating protection Short-circuit between motor phases Against input phase loss in three-phase Thermal motor protection via the drive by continuous calculation of I²t |
Quantity per set | Set of 1 |
width | 72 mm |
height | 143 mm |
depth | 102.2 mm |
net weight | 0.7 kg |
Reviews
There are no reviews yet.